I. OVERVIEW
This product of Hybrid And Electric Car Training adopts plug-and-play or swipe card mode; it has the functions of full self-stop, overload, overcurrent, short-circuit and overvoltage protection.
II. Product parameters
|
Attributes |
Parameters |
|
Operating Voltage |
220±10 |
|
Standby power |
3.5W |
|
Single output power |
7000W |
|
Working Temperature |
-40 ~80° humidity less than 90% |
|
Measuring precision |
Port independent measurement, first class standard |
|
Material technology |
Engineering PC flame retardant waterproof material |
|
Protection mode |
Overload, overcurrent, short circuit, overvoltage protection |
|
Power failure mode |
Full self-stop, no-load self-stop, timing end |
|
Charging prompt |
Voice, buzzer, indicator |
|
Dimension |
30cm*24cm*8cm |
2.1 Function Introduction
2.1.1 Human-computer interaction interface
Automatic full mode and manual charging mode can be selected.
With automatic filling mode: the charging pile dynamically adjusts the data parameters according to the data provided by the battery management system at the vehicle end, performs the corresponding actions and completes the charging process.
Display output function: real-time display of charging voltage, charging current, power, circuit board temperature, fault information and other information.
It can correspondingly display the relevant information under each state of the charging pile, display the corresponding prompt information when there is a fault, and display the monitoring unit.
2.2 Environmental requirements
The protection level of the AC charging post is IP55. In order to ensure the safe and efficient operation of the charging post, please observe the following items when selecting the installation environment.
The installation space is free of combustible gas and flammable items
The installation floor is dry and flat; stagnant water on the floor is strictly prohibited; make sure that the floor is level without shaking and can fully carry the weight of the machine.
The ambient temperature range of the installation location is -25℃~+50℃, and the relative humidity range is 0~95% (no condensation).
Enough distance is reserved around the charging pile to ensure ventilation and heat dissipation, installation and maintenance, and safety escape
Charging pile operation should avoid direct sunlight in high temperature environment, avoid close to strong heat source
Installation location should ensure that it is convenient to observe the LED liquid crystal
III. Application Scenario
Intelligent shared charging socket can be widely used in various public parking lots as well as communities, neighborhoods, office buildings and industrial parks to provide safe, intelligent and convenient charging services for the majority of electric vehicle owners.
IV. List of products
|
Product name |
Picture |
Qty |
Remark |
|
The host of Hybrid And Electric Car Training |
|
1 |
Standard |
|
Backplane |
|
1 |
|
|
Charging Gun Hanger |
|
1 |
Standard |
|
Installation of column |
|
1 |
Optional |
4.1 Cable specification
7KW single gun: 6 square meters
If the connecting cable specification is different from the recommended cable in the above table, the selected cable specification should meet the overcurrent and voltage requirements with sufficient margin, and the cable on the same side should be of the same specification.
Please refer to 2.3 Electrical Parameters for input and output current and voltage of charging pile.
4.2 Wiring area
The AC input terminals of the charging post are located in the back cover of the machine, when connecting the input cable, please introduce the 5-core cable into the machine through the waterproof connector at the bottom of the chassis, and connect it to the specified position according to the phase sequence.
Each terminal is clearly labeled. As shown in the figure below
Charging pile electrical connection location
|
Cable |
Name |
|
L/N |
Charging pile AC input |
|
PE |
Grounding |
V. Troubleshooting
The charging pile is in fault or alarm state: the charging pile is disconnected from charging, the red indicator light is always on, and the touch screen displays the corresponding fault or alarm information state.
When the charging pile has a fault or alarm, you can check the fault and alarm information by checking the history information.
If you can't deal with the fault, please record the detailed data and contact the relevant personnel of the company.
Only professional electricians or professionally qualified persons should operate on the contents of this chapter
|
Basic Failure Types |
Cause analysis |
Conventional treatment methods |
Remark |
|
AC input overvoltage/undervoltage |
1. Abnormal grid voltage 2. Software parameter setting error |
Please check if the voltage on the AC input side is too high or too low. |
|
|
Output overcurrent |
Abnormal output current |
Please check whether the output current is within the parameter setting range, if not please check whether the output current is too high |
|
|
Charge Gun Connection Failure |
Charge gun disconnected |
Please check if the charging gun is connected in place |
|
|
Emergency stop |
Emergency stop button pressed |
Check that the emergency stop button is not pressed |
|
|
Card failure |
Card locked or card reader malfunctioning |
1. Please check whether the display prompt card is locked 2. The wiring of the card reader is incorrect or the card reader is invalid |
VI. Quality Assurance
If the product of Hybrid And Electric Car fails during the warranty period, our company will repair or replace the new product free of charge. The product is guaranteed for 12 months from the date of shipment.
The company has the right not to carry out quality assurance in the following cases
The whole machine and parts have exceeded the free warranty period
Transportation damage
Incorrect installation, modification or use
Operation in very harsh environments beyond those described in this manual
Failure or damage to the machine caused by installation, repair, modification or dismantling by persons other than the Company's service organization or personnel.
Failure of or damage to the machine caused by the use of non-standard parts.
Any installation or use outside the scope of the relevant international standards.
Damage caused by abnormal natural environment
Due to product upgrades, the contents of the manual may deviate from the actual product, please refer to the actual product.
Due to product upgrades, the contents of the manual will be modified or adjusted without prior notice.
